Hp Msa 2040 San Storage User Manual

Advertising

Feb 22, 2017 ADD new Server to a SAN network, zone in SAN switch and map in the msa2040, then connect to disks in win server 2012.

HP MSA 2040
User Guide

This guide provides information for setting up, conﬁguring, and administering the HP StorageWorks All-in-One Storage Systems. HP StorageWorks 400 All-in-One Storage System. HP StorageWorks 600 All-in-One Storage System. HP StorageWorks 1200 All-in-One Storage System. HP MSA Storage Replication Adapter Software User Guide Abstract The HP MSA Storage Replication Adapter (SRA) Software for VMware® vCenter Site Recovery Manager (SRM) enables full-featured use of the VMware SRM with HP MSA 2040 and HP MSA P2000 G3 storage systems. This guide provides information for setting up, conﬁguring, and administering the HP StorageWorks All-in-One Storage Systems. HP StorageWorks 400 All-in-One Storage System. HP StorageWorks 600 All-in-One Storage System. HP StorageWorks 1200 All-in-One Storage System.

HP Part Number: 723983-002

4 Technical white paper HP MSA 2040 Storage Configuration and Best Practices for VMware vSphere Figure 1. The HP MSA 2040 Storage array All HP MSA Storage models offer a common set of features listed in Table 1. Feb 22, 2017 ADD new Server to a SAN network, zone in SAN switch and map in the msa2040, then connect to disks in win server 2012. User Manuals, Guides and Specifications for your HP MSA 2040 Chassis, Controller, I/O Systems, Network Hardware, Storage, Transceiver. Database contains 12 HP MSA 2040 Manuals (available for free online viewing or downloading in PDF): Firmware release notes, Replacement instructions, Quickspecs, Troubleshooting manual, Operation & user’s.

Published: September 2013

Edition: 2

Abstract

This document describes initial hardware setup for HP MSA 2040 controller enclosures, and is intended for use by storage system

administrators familiar with servers and computer networks, network administration, storage system installation and configuration,

storage area network management, and relevant protocols.

Advertising

Table of contents

Overview
- MSA 2040 Storage models
Components
- Front panel components
- Controller enclosure-rear panel layout
- Drive enclosures
Installing the enclosures
- Connecting controller and drive enclosures
- Powering on/powering off
  - DC and AC power supplies equipped with a power switch
Connecting hosts
- Connecting the enclosure to data hosts
  - MSA 2040 SAN
  - Connecting direct attach configurations
  - Connecting switch attach configurations
- Connecting two storage systems to replicate volumes
  - Host ports and replication
Connecting to the controller CLI port
- Device description
- Obtaining IP values
- Using the CLI port and cable-known issues on Windows
Basic operation
Troubleshooting
- Fault isolation methodology
  - Options available for performing basic steps
  - Performing basic steps
- Diagnostic steps
- Controller failure in a single-controller configuration
- Isolating a host-side connection fault
- Isolating Remote Snap replication faults
  - Diagnostic steps for replication setup
- Resolving voltage and temperature warnings
Support and other resources
- Contacting HP
- Related information
LED descriptions
- Front panel LEDs
- Rear panel LEDs
  - Controller enclosure-rear panel layout
Environmental requirements and specifications
- Site requirements and guidelines
- Electrical requirements
Electrostatic discharge
SFP option for host ports

Popular Brands

Popular manuals

Advertising

Connecting two storage systems to replicate volumes

The diagram below shows host interface connections and replication, with I/O and replication occurring

on different networks. For optimal protection, use two switches. Connect two ports from each controller

module to the first switch to facilitate I/O traffic, and connect two ports from each controller module to the

second switch to facilitate replication. Using two switches in tandem avoids the potential single point of

failure inherent to using a single switch; however, if one switch fails, either I/O or replication will fail,

depending on which of the switches fails.

Figure 27 Connecting two storage systems for Remote Snap: multiple servers/switches/one location

Virtual Local Area Network (VLAN) and zoning can be employed to provide separate networks for iSCSI

and FC, respectively. Whether using a single switch or multiple switches for a particular interface, you can

create a VLAN or zone for I/O and a VLAN or zone for replication to isolate I/O traffic from replication

traffic. Since each switch would include both VLANs or zones, the configuration would function as multiple

networks.

Multiple servers/different networks/multiple switches

The diagram below shows the rear panel of two MSA 2040 SAN controller enclosures with both I/O and

replication occurring on different networks.

Figure 28 Connecting two storage systems for Remote Snap: multiple servers/switches/two locations

The diagram below also shows the rear-panel of two MSA 2040 SAN controller enclosures with both I/O

and replication occurring on different networks. This diagram represents two branch offices cabled to

enable disaster recovery and backup. In case of failure at either the local site or the remote site, you can

fail over the application to the available site.

6Gb/s